Diy Turkey Fan And Wing Mount

Cut along the underbelly, making a slit from the anus to where the feathers end just below the beak. I also clean and remove all meat from the wingbones and at the base of the tail.

Turkey Fan Mount, taxidermy done by the Mad Taxidermist

I start by skinning the turkey.

Diy turkey fan and wing mount. It has, by far, been my most popular post. Turkey fan mount / turkey fan with photo / turkey hunting / turkey fan / turkey fan plaque / first turkey / custom photo on wood / turkey Diy turkey fan and beard display kit.

Lay out the feathers on a piece of cardboard and use straight pins to tack them into a fan shape. I then lay the hide feathers down. I clean all the meat off the hide.

The fan will be gently held in place with spring tension. You'll need to skin alongside the bird's flanks the farther down the back you go. I then painted the whole bone and adjacent wing area with some thinned epoxy to seal it so to speak and clean it up.

Take your time, as turkey skin is thin. There is a slot cut for the beard, and two slots cut to mount the turkey legs to display the spurs. I had over 270 downloads of the plan.

Once dry, i mixed up some bondo and applied it to the area in between the wing bones and around the wire. We even offer custom carving on most of our turkey fan mounting plaques to help you remember the hunt. You can get all our wild turkey tail mounting kits with or without the turkey laser on the front of the plaque.

Premium shot shell turkey fan mount (3 pack) bulk for taxidermy shops large size trophy fan display plaque copper for a real shot shell look, by far the best looking turkey mounts, sleek clean look. As with any taxidermy mount, the quality you end up with depends on how well you take care of the fan feathers. I also did a mount like you are describing.

Brush off the loose borax and mix up a small batch of bondo car body putty. Make underwing cuts and clean all meat. Double fan w/picture display $ 60.00 select options

The plan was designed to be printed out full scale, on an 11x17 ledger size piece of paper. Then, skin the turkey out. Turkey fan and wing mounting kit.

As far as how to mount a turkey fan, start by liberally spreading an equal mixture of table salt and borax onto the flesh and throughout the base of the quills on the back side, using your gloved hands to massage it in. Some great custom turkey fan mount ideas would be you could add your shell casings, or even the date when you shot your bird. 4.1 out of 5 stars54.

Be sure to leave a little extra flesh on both to hold the bristles and feathers in place. I cut through the skin from the carauncles to the anus. Take extra care in the field and transporting the fan.

3/4 + 3/4 = 1 1/2, so i needed to shave a bit off the thickness of my newly joined boards on the table saw, bringing it down to the 1 1/4 size of my turkey fan. Wire the wings with heavy wire. Begin your project by carefully removing the beard and tail fan with a sharp knife.

April 4, 2013 2 comments. Simply choose the wood of your choice. Next comes the tricky part.

two turkey wing feathers, tail feather fan and beard. Premium shot shell turkey fan mount (3 pack) bulk for taxidermy shops large size trophy fan display plaque copper for a real shot shell look, by far the best looking turkey mounts, sleek clean look. Blow the marrow out of the bones.

Using double sided tape, i affixed the templates to their respective pieces.in the past, i have used spray adhesive, glue sticks, and even wood glue to do this, but it always ends up being a cleanup nightmare. You could add both if youd like. Just make sure its legal.

When it cured, it really made the wing joints very solid and gave me a great plate to drill through for precise mounting. Gently skin away toward the direction of the tail fan, retaining as much of the skin with attached feathers as possible. Lay the tail on cardboard or old newspapers and peel back the skin from the flesh toward the feathers on both sides to expose the knob of flesh and bone that holds all of the tail feather quills.

It doesnt matter if its a gobbler or a hen; We have turkey mount plaques available with carved tracks, a laser engraved strutting turkey, a picture kit, or even with multiple beards. I just did my first 2 lifesize turkey.

The plaque has a keyhole cut in the back for flush mounting to the wall. First, acquire a freshly killed turkey. With the glue dried, i traced the patterns onto the wood heavily with a ballpoint pen, then removed the patterns and traced over the dents left behind in the wood.

Finish the wood plaque as you desire. You will provide the wood. War bird indian face turkey wing mount.

If you want to save a fan mount like the one shown, here are the basic steps to follow. Follow along as i show you how i clean, pin an. Jakeswoodworkingin 5 out of 5 stars (116) $ 67.00.

Turkey fan and wing mounting kit war bird indian face turkey wing mount elk skulls mule deer skulls antelope skulls caribou skulls reproduction ram skull pour spouts camo patterns antler mounting instructions men's apparel women's apparel This is a turkey fan and beard display made from reclaimed barn wood. This is a diy kit.

The edges have not been routed for more of a rustic look to the plaque. This will dry and preserve the tail fan base, which keeps it. Our turkey mounting kits are available in oak, walnut, cedar, and weathered wood.

Cover and let the dry for two to three weeks in a dry safe place. Slowly and meticulously, begin separating the skin from the meat. Here are my rug mount directions.

Free shipping on orders over $25 shipped by amazon. Place the fan in a refrigerator for a few days or freezer until you are ready to proceed. If you've done birds it's really no big deal.

Laser Engraved single turkey fan with wing mount with